Aluminium

This week we talk about the removal process is actually the aluminum windows in preparation for the installation of vinyl replacement Windows. Start with a horizontal sliding window, which is rather vague at the national level. This is a sliding panel and a panel of detention. To remove the first cursor. All you need to do is open the slide cover, grasp the sides of the panel with your hands to lift, tilt e. In an ideal situation, it would be so easy. However,There are small obstacles that may prevent the lifting of the panel.

Many sliding windows have rollers on the top and bottom. The top rollers do not actually do anything more than replace the bottom rollers when they wear to replace. But often the installer window adjust these rollers to prevent anyone from top to raise the panel. If this is the case with windows, and a screw on top of each side rail. If you solve theseScrews, then lift the panel should come. Another obstacle relates to a small piece of rubber that the manufacturer is running the track. This piece of rubber has the same effect as adjusting the rollers at the top. It prevents you from lifting out of the jury, because wedged between the top of the window and the top of the track above. When you see that are not windows and not raise all the way to the running rail and the rollers of the ground, then you have to digemphasized that piece of rubber. Is usually somewhere in the middle, where the sliding and fixed panel overlap when the window is closed. Arrive with a long thin screwdriver, and try to pull it out.

Once off the lever, remove the screen. You can simply pull out. No need to be nice, because you're throwing it away anyway. The last step is to remove the fixed panel. There are a few different applications here. Everyone has a vertical center line. Is usuallyaccept there block the slider, but not always. Locate the screws, rather than with those of the center of the bar. They are both on top and bottom outside, or you can view on the canal side, where he found the screen. Check the corners top and bottom.

Say that you are getting the screws removed, it is now necessary to raise the center bar. Take a screwdriver and a hammer and tap the bar at the bottom. Tap fixed before the frame of the panel. Now consider the fixedPanel away from the side where it rests in the side channel. What are you trying to do, is the fixed panel open the same way that you are sliding the slide. Then you can lift the fixed panel up outside. At times, the fixed panel is not to slide open, because it got to the page length. You can put a screwdriver into the side channel and disconnect the panel set by the page. No matter if the frame is still attached to the Bend of the house, because weTo hide all this anyway.

Now we go back to the vertical center bar and assume you do not remove the screws to it. That is, not the piece of glass, surrounded by a frame. E 'in both caulk with silicone, glass or foam tape, double-click. You have to cut the glass, then the bar center, with a saber saw. In general, "help stop" on the outside of the piece of glass in place. There are 4 of them, a top, bottom, and eachSide. You should be able to understand with just a screwdriver. Then you can go in and cut away the adhesive holding the glass of the frame. Use a utility knife and cut between the glass and frame. Wear gloves and be careful not to hand through the glass. Place a sheet or tarpaulin outside and let the glass fall into it. In addition, you can get a stand of support on a scale above the glass and try, grabbed the top edge as you cut out of the frame. Allow your assistants also gloves.The reason for the scale you have the glass in case you have a small crack that you can not see. Once you grab the glass, the crack will run on the opposite side, and suddenly you are tempted to put more pieces of glass in the same period. Since the scale, when the glass "runs", let you go. After the glass, cut the bottom of the bar center of the track flush with the ground. Then you can move the bar back and forth to break the headScrew free. You can download it for deletion, panoramic windows that do not have a sliding panel. To treat them as you have the fixed part, without having to remove a bar downtown.

Next week we will discuss the differences between the installation of vinyl replacement frame and a vinyl retrofit frame.

Visit : อลูมิเนียมคอมโพสิท aluminium composite แคลดดิ้ง